Fuel properties and incineration behavior of poultry litter blended with sweet sorghum bagasse and pyrolysis oil.

The incineration of poultry litter (PL) effectively reduces the volume of waste in line with the United Nations Sustainable Development Goal of "affordable and clean energy". However, mono-incineration is associated with considerable challenges due to the varying moisture, structural and chemical composition and low energy yield. The aim of the present work was to investigate the influence of sweet sorghum bagasse (SS) and pyrolysis oil (PO) on improving the fuel properties of PL and mitigating ash related burdens during incineration. The different biomass feedstocks were produced by combining PL with SS at 0.0% (T0), 25% (T1), 50% (T2), 75% (T3) and compared with 100% SS (T4). In order to achieve high energy potential and low ash deposition, the parallel samples were additionally mixed with 10% PO to improve the energy value. The experimental results show that increasing the proportion of SS and adding PO to the mixtures increases the volatile matter and decreases the moisture and ash content. The addition of PO also increases the carbon and hydrogen content. The use of SS and PO thus increased the values of the ignitability index and apparently also the flammability by 30.0%-49.4% compared to pure PL. SS and PO shifted the HHV of the starting material from 16.90 to 18.78 MJ kg-1. In addition, SS + PO improved the flame volume and red color intensity of the PL blends based on the image analysis method. However, the presence of SS and PO did not sufficiently improve the ash-related index values, which requires further investigation.

Solidification/stabilization and optimization of municipal solid waste incineration fly ash with aluminosilicate solid wastes.

Alkali-activation is an effective municipal solid waste incineration fly ash (MSWIFA) solidification/stabilization (S/S) technology. However, the characteristics of calcium-rich silica-poor aluminum phase in MSWIFA easily cause the structural instability and contamination of alkali activated MSWIFA S/S bodies. Therefore, the aluminosilicate solid wastes are used in this work to optimize the immobilization and structural properties. Results showed that incorporation of aluminosilicate solid wastes significantly improved the compressive strength and heavy metals pollution toxicity of MSWIFA S/S bodies. Compared to alkali activated MSWIFA, the compressive strength of S/S bodies with addition of coal fly ash, silica fume and granulated blast furnace slag improved by 31.0%, 47.6% and 50.8% when the curing time was 28 days, respectively. Leachability of Pb, Zn and Cd in these alkali activated MSWIFA S/S bodies was far below the threshold value specified in Standard GB16889. Aluminosilicate solid wastes provided abundant Si/Al structural units, and some new phases such as ettringite(AFt, 3CaO⋅Al2O3⋅3CaSO4⋅32H2O), calcium sulfoaluminate hydrate (3CaO⋅Al2O3⋅CaSO4⋅12H2O) and Friedel's salt (CaO⋅Al2O3⋅CaCl2⋅10H2O) can be detected in S/S matrix with aluminosilicate solid wastes, along comes increased the amount of the amorphous phases. Lower Ca/Si molar ratio tended to form the network structure gel similar to tobermorite with higher polymerization degree. Meanwhile, the silica tetrahedron of the gels changed from the oligomerization state like island to the hyperomerization state like chain, layer network or three-dimensional structure, and average molecular chain length increased. These findings provide theoretical basis for structural properties optimization and resource utilization of MSWIFA S/S matrices.

Medical waste incineration fly ash-based magnesium potassium phosphate cement: Calcium-reinforced chlorine solidification/stabilization mechanism and optimized carbon reduction process strategy.

The traditional solidification/stabilization (S/S) technology, Ordinary Portland Cement (OPC), has been widely criticized due to its poor resistance to chloride and significant carbon emissions. Herein, a S/S strategy based on magnesium potassium phosphate cement (MKPC) was developed for the medical waste incineration fly ash (MFA) disposal, which harmonized the chlorine stabilization rate and potential carbon emissions. The in-situ XRD results indicated that the Cl- was efficiently immobilized in the MKPC system with coexisting Ca2+ by the formation of stable Ca5(PO4)3Cl through direct precipitation or intermediate transformation (the Cl- immobilization rate was up to 77.29%). Additionally, the MFA-based MKPC also demonstrated a compressive strength of up to 39.6 MPa, along with an immobilization rate exceeding 90% for heavy metals. Notably, despite the deterioration of the aforementioned S/S performances with increasing MFA incorporation, the potential carbon emissions associated with the entire S/S process were significantly reduced. According to the Life Cycle Assessment, the potential carbon emissions decreased to 8.35 × 102 kg CO2-eq when the MFA reached the blending equilibrium point (17.68 wt.%), while the Cl- immobilization rate still remained above 65%, achieving an acceptable equilibrium. This work proposes a low-carbon preparation strategy for MKPC that realizes chlorine stabilization, which is instructive for the design of S/S materials.

Effect of long-term dry-wet circulations on the Solidification/stabilization of Municipal solid waste incineration fly ash using a novel cementitious material.

Solidification/stabilization (S/S) is a typical technique to immobilize toxic heavy metals in Municipal solid waste incineration fly ash (MSWI FA). This study utilized blast furnace slag, steel slag, desulfurization gypsum, and phosphoric acid sludge to develop a novel metallurgical slag based cementing material (MSCM). Its S/S effects of MSWI FA and long-term S/S effectiveness under dry-wet circulations (DWC) were evaluated and compared with ordinary Portland cement (OPC). The MSCM-FA block with 25 wt.% MSCM content achieved 28-day compressive strength of 9.38 MPa, indicating its high hydration reactivity. The leaching concentrations of Pb, Zn and Cd were just 51.4, 1895.8 and 36.1 µg/L, respectively, well below the limit standard of Municipal solid wastes in China (GB 16889-2008). After 30 times' DWC, leaching concentrations of Pb, Zn and Cd for MSCM-FA blocks increased up to 130.7, 9107.4 and 156.8 µg/L, respectively, but considerably lower than those for OPC-FA blocks (689, 11,870.6 and 185.2 µg/L, respectively). The XRD and chemical speciation analysis revealed the desorption of Pb, Zn and Cd attached to surface of C-S-H crystalline structure during the DWC. The XPS and SEM-EDS analysis confirmed the formation of Pb-O-Si and Zn-O-Si bonds via isomorphous replacement of C-A-S-H in binder-FA blocks. Ettringite crystalline structure in OPC-FA block was severely destructed during the DWC, resulting in the reduced contents of PbSO4 and CaZn2Si2O7·H2O and the higher leachability of Pb2+ and Zn2+.

Recovery of Zn and Cu from municipal solid waste incineration fly ash by integrating ammonium leaching and ammonia removal.

This study introduces an environmentally friendly process for recovering zinc (Zn) and copper (Cu) from municipal solid waste incineration (MSWI) fly ash using ammonium chloride leaching and ammonia removal. The leaching rates for Zn and Cu were 54.39% and 86.23%, respectively, with total recovery rates reaching 52.21% and 85.28%, respectively. The recovered precipitate demonstrated significant Zn (33.62%) and Cu (14.19%) contents, making it ideal for metal smelting. The ammonium leaching process also showcased effective reduction and dechlorination effects on the fly ash. The treated fly ash had a reduced mass of only 30.63% of the original, and chlorine content decreased from 26.23% to 0.84%. The results of this study support the sustainable utilization of MSWI fly ash by facilitating valuable resource recovery and promoting its conversion into construction materials.

Photodegradation of 2-chlorodibenzo-p-dioxin (2-CDD) on the surface of municipal solid waste incineration fly ash: Kinetics and product analysis.

Considering that waste incineration fly ash is the main carrier of dioxins and can migrate over long distances in the atmosphere, it is of great significance to study the photochemical transformation behavior of dioxins on the surface of fly ash. In this work, 2-chlorodibenzo-p-dioxin (2-CDD) was selected to conduct a systematic photochemical study. The influence of various factors on the photodegradation of 2-CDD were first explored, and the results showed that small particle size of fly ash, low concentration of 2-CDD and appropriate level of humidity were more conducive to photodegradation, with the highest degradation percentage reaching 76%-84%. The components of fly ash (Zn (Ⅱ), Al (Ⅲ), Cu (Ⅱ) and SiO2) also had a certain promoting effect on the degradation of 2-CDD, which increases the degradation efficiency by 10%-20%, because they could act as effective photocatalysts to produce free radicals for reaction. With a higher total light exposure intensity, natural light environments led to a more complete degradation of 2-CDD than laboratory Xe lamp irradiation (90% degradation Vs. 79% degradation). Based on chemical probe and radical quenching experiment, hydroxyl radical also contributed to 2-CDD photodegradation on fly ash. A total of 16 intermediate products were detected by mass spectrometry analysis, and four initial reaction pathways of 2-CDD were speculated in the process, including dechlorination, ether bond cleavage, hydroxyl substitution, and hydroxyl addition. According to the results of density functional theory calculation, the reaction channels of ether bond cleavage and •OH attack were determined. The toxicity assessment software tool (TEST) was used to assess the toxicity and bioconcentration coefficient of reaction products, and it was found that the overall toxicity of the photodegradation products was reduced. This study would provide new insights into the environmental fate of dioxins during long-range atmospheric migration process.

Use of municipal solid waste incineration (MSWI) bottom ash as a permeable subgrade material: An experimental and mechanism study.

As a traditional method of waste treatment, municipal solid waste incineration (MSWI) has become one of the main methods of urban waste treatment. However, as a byproduct of MSWI, a large amount of MSWI bottom ash is not reused in current practice. This study innovatively posits MSWI bottom ash as an eco-friendly adsorbent rather than a pollutant, exploring its potential application as a permeable subgrade material. The results reveal that MSWI bottom ash exhibits promising properties to serve as a permeable subgrade material to achieve the permeability and improve the sustainability for subgrade. Due to the arrangement of its particles, it shows excellent performance in shear strength and permeability, which are comparable to or surpass those of sandy soils. The average pore width of 14.200 nm allows heavy metal substances to be encapsulated within the matrix, significantly reducing their leachability, thereby aligning with environmental friendliness standards. Its adsorption capacity is about 6.60 mg/g, and the adsorption capacity per volume is 3.66 times and 2.04 times that of fly ash and clay, respectively. The mechanism analysis shows that the adsorption process is monolayer heterogeneous adsorption. This paper presents a novel perspective on reusing MSWI bottom ash and provides evidence supporting its effective utilization as a permeable subgrade material, offering substantial environmental benefits through enhanced adsorption ability.Implications: Municipal solid waste incineration (MSWI) is a common method for municipal solid waste treatment, while the MSWI bottom ash is often not reused. This paper explored the explores the feasibility of using MSWI bottom ash as a permeable road base material. The results show that the particle arrangement enables excellent shear strength and permeability, comparable to sandy soil. It meets safety requirements for the leaching of heavy metals and acts as an adsorbent for pollutants leaching from permeable pavements. Furthermore, the mechanisms underlying these behaviors of MSWI were confirmed by microstructural and mineralogical analyses. These indicate that MSWI bottom ash has great potential as a permeable road base material. This paper provides a clear understanding of the physical, mechanical and environmental properties of MSWI bottom ash, which can promote its reuse in practice.

Distribution of gasification products and emission of heavy metals and dioxins from municipal solid waste at the low temperature pyrolysis stage.

Gasification is widely regarded as one of the most practical, economical, and environmentally friendly waste disposal technologies for municipal solid waste (MSW). The pyrolysis stage (300-500 °C) is crucial for weight loss during MSW gasification, as a considerable amount of organic matter breaks down, producing high-value synthesis gas. This study investigated the product distribution and pollutant emission characteristics within this temperature range and its influencing factors during MSW gasification using a self-designed MSW gasification device. Results indicated that MSW underwent approximately 70% weight loss within this temperature range, yielding low amounts of inorganic and short-chain organic products, with mainly long-chain organic compounds of C16-C34. The atmosphere variation had minimal effect on the elemental composition and content of solid phase products. X-ray fluorescence spectrometry (XRF) and inductively coupled plasma mass spectrometry (ICP-MS) analyses showed that Mn and Zn were the primary components of heavy metal leaching toxicity in solid phase products, with their contents increasing as temperature increased. Synthesis gas showed the highest content of heavy metal As element, reaching a peak at 400 °C. Higher gasification temperature and lower oxygen flow rate significantly reduced the dioxin content and I-TEQ values, with highly chlorinated isomers being the predominant dioxin isomers. Nonetheless, low-chlorinated dioxins accounted for more than 50% of the I-TEQ. This study improves our understanding of the gasification process of MSW.

Highly efficient carbonation and dechlorination using flue gas micro-nano bubble for municipal solid waste incineration fly ash pretreatment and its applicability to sulfoaluminate cementitious materials.

Cement production is a primary source of global carbon emissions. As a hazardous waste, municipal solid waste incineration fly ash (MSWI-FA) can be pretreated as a cementitious and effective carbon capture material. This study proposes an efficient carbonation dechlorination pretreatment and resource recovery strategy using flue gas micro-nano bubble (MNB) to wash MSWI-FA. The results showed that the flue gas MNB water washing reaction solution inhibited CaCO3 boundary layer blocking and adsorption on NaCl and KCl leaching. Under low water-to-solid ratio and CO2 concentration conditions, two-step washing reduced the MSWI-FA chlorine content to <1%, improving the dechlorination effect by 19.72% compared to conventional carbonation. The flue gas MNB water accelerated the precipitation of Ca2+ and Ca(ClO)2 in the form of calcite. The higher the CO2 concentration in the flue gas MNB, the better the fragmentation and purification of the MSWI-FA shell, leading to improved dechlorination and CO2 fixation. Under optimized conditions, the mean particle size of MSWI-FA decreased by 47.82%, and the CO2 fixation rate reached 73.80%, with a 58.35% increase in the washing carbonation rate. MSWI-FA pretreated by flue gas MNB washing was used as both the raw material and supplementary cementitious material for sulfoaluminate cementitious (SAC) material, exhibiting excellent compressive strength and heavy metal stabilization. The maximum compressive strength of the MSWI-FA-based SAC material cured for 28 d reached 130 MPa. Cr leaching was inhibited with increased hydration time, and the leaching concentration was far below the standard limit.

Dioxins emissions from bio-medical waste incineration: A systematic review on emission factors, inventories, trends and health risk studies.

COVID-19 has aggravated the biomedical waste generation all over the world and the concern for its safe disposal is on the rise. The vast majority of healthcare systems employ incineration as their treatment method considering its agility to reduce the waste volume by up to 95-96% and high-temperature inactivation of infectious biological materials. However, incinerator emission is a significant contributor of polychlorinated dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs) and dioxin-like polychlorinated biphenyls (dl-PCBs) according to various national inventories across the globe. Bio-Medical Waste Incinerators (BMWIs) are the dominant form of incinerator plants in developing nations and hence BMWI emissions were found to contribute lion's share of national dioxins inventories in most of these countries. The Stockholm Convention on POPs played a key role in imbibing significant urge on the dl-POPs monitoring studies of incinerators internationally and on controlling the average incinerator emission levels. Though many national/international agencies endorse a stringent incinerator stack emission standard of 0.1 ngTEQ/Nm3, there are some differences observed in nation-to-nation regulatory scenarios. This paper reviews and reports on the dioxins emission and health risk studies associated with bio-medical waste incineration over the last three decades (1990-2020) with a comprehensive spatial and temporal emission trend analysis. An overview of important national and international regulations, national inventories and emission factors for the biomedical waste incineration sector is also reviewed in detail. The study observes that continuous regulatory monitoring and logical relaxations can enhance the performance of the existing facilities ensuring low emissions and minimal risk.

Converting ash into reusable slag at lower carbon footprint: Vitrification of incineration bottom ash in MSW-fueled demonstration-scale slagging gasifier.

Globally waste incineration is becoming the predominant treatment method of solid waste. The largest fraction of solid residue of this process is incineration bottom ash (IBA) requiring further treatment before applications such as in the construction industry become feasible. In this study, vitrification of IBA was conducted in a demonstration-scale high-temperature slagging gasification plant fueled with MSW and biomass charcoal as a green auxiliary fuel. High IBA co-feeding rates of up to 491 kg/h (equivalent to 107% of MSW feeding rate) were achieved during the trials. A highly leaching-resistant slag immobilizing heavy metals in the glass-like amorphous structure and recyclable iron-rich metal granules were generated in the process. The heavy metal migration into the solid by-product fractions depended on the IBA feeding rates and process conditions such as cold cap temperature, charcoal-to-ash ratio, and gasifier temperature profile. Slaked lime and activated carbon powder were used in a dry flue gas treatment and stack gas emissions were kept well below Singapore's regulatory limits. Steam from the hot flue gas was generated in a boiler to drive a steam turbine. The application of biomass charcoal instead of fossil fuels or electricity lead to a lower carbon footprint compared to alternative vitrification technologies. The overall results reveal promising application of high temperature slagging gasification process for commercial-scale vitrification of IBA.

Characterization of different solid fuels from waste for an advanced online fuel control system designed for large-scale incineration plants.

Despite many years of experience in the incineration of solid fuels from waste, the heterogeneity of solid fuels and their varying properties still pose a challenge for a stable and clean combustion in large-scale incineration plants. In modern facilities such as municipal waste incineration plants there still exists a lack of knowledge on the exact amount and calorific value of waste entering onto the grate. Based on the works of Warnecke et al. and Zwiellehner et al., in our project 'AdOnFuelControl', we determined the initial bulk density at the feed hopper by measuring the weight of the waste via the crane weigher and the volume via a high-performance 3D laser scanner. With the help of the determined bulk density, the lower heating value (LHV) and the compression in the feed hopper were calculated. All this information was integrated into the combustion control system, which provided a high potential for an optimized operation of the plant. In this article, six different fuels (fresh and aged municipal solid waste, refuse-derived fuel (fluff), refuse-derived fuel (fine grain), waste wood and dried, grained sewage sludge) were examined for the elemental composition, the LHV, fuel-specific parameters and the compression behaviour. In addition, initial tests with the 3D laser scanner as well as formulas for the calculation of the density in the feed hopper were presented. Based on the results of the experiments, the chosen approach seems very promising for optimized combustion control in large-scale incineration plants. As a next step, the gained knowledge and technology should be integrated in the municipal waste incineration plant.

Environmental and economic assessments of industry-level medical waste disposal technologies - A case study of ten Chinese megacities.

Medical waste (MW) is exploding due to the COVID-19 pandemic, posing a significant environmental threat, and leading to the urgent requirement for affordable and environmentally friendly MW disposal technologies. Prior research on individual MW disposal plants is region-specific, applying these results to other regions may introduce bias. In this study, major MW disposal technologies in China, i.e., incineration technologies (pyrolysis incineration and rotary kiln incineration), and sterilization technologies (steam sterilization, microwave sterilization, and chemical disinfection) with residue landfill or incineration were analyzed from an industry-level perspective via life cycle assessment (LCA), life cycle costing (LCC) and net present value (NPV) methods. Life cycle inventories and economic cost data for 4-5 typical companies were selected from 128 distinct enterprises and academic sources for each technology. LCA results show that microwave sterilization with residue incineration has the lowest environmental impact, emitting only 480 kg CO2 eq. LCC and NPV analyses indicate that steam sterilization with landfilling is the most economical, yielding revenues of 1,210 CNY/t and breaking even in the first year. Conversely, pyrolysis and rotary kiln incineration break even between the 4th and 5th years. Greenhouse gas emissions from the MW disposal in ten cities with the largest MW production in 2020 increased by 7% over 2019 to 43,800 tons and other pollutants increased by 6% to 12%. Economically, Shanghai exhibits the highest cost-effectiveness, while Nanjing delivers the lowest. It can be observed that the adoption of optimal environmental technologies has resulted in a diminution of greenhouse gas emissions by 279,000 tons and energy conservation of 1.76 billion MJ.

Improved method for calculating CO2 emission from industrial solid wastes combustion system based on fossil and biogenic carbon fraction.

Waste-to-Energy (WtE) technology is the most effective solution for managing non-recyclable wastes through mass burning and energy recovery. Owing to the significant volumes of plastics in China's industrial solid wastes (ISW), a large amount of greenhouse gases (GHG) is generated during the incineration process. Therefore, monitoring GHG emissions from WtE facilities is essential. Owing to the lack of suitable accounting models and characterized fossil carbon fraction (FCF) data, current studies use default values provided by the Intergovernmental Panel on Climate Change's (IPCC), which increases calculation inaccuracies. Therefore, this study established an improved method to accurately account for carbon emissions during solid waste incineration by firstly using radiocarbon dating by accelerator mass spectrometry (AMS) technique to determine the FCF of the solid waste components in China. Monte Carlo analysis was employed to perform the sensitivity analysis, and the results indicated that there was a significant deviation between the measured value and IPCC's default values of FCF, 3.2, 32.48, 93.39, 93.76, 90.49, and 93.8 % for paper, cotton, synthetic textiles, artificial rubber, artificial leather, and plastics, respectively. By replacing coal with ISW in a 2 × 110 t/h circulating fluidized bed boilers, 9.251 × 104 t CO2-eq emissions were reduced, and the carbon emission factor reached 0.56 t CO2-eq/t waste. This study complements the research gap fossil carbon data of wastes in the IPCC guidelines and provides a more accurate and effective way to calculate carbon emissions during ISW incineration treatment.

Transformation behavior of heavy metal during Co-thermal treatment of hazardous waste incineration fly ash and slag/electroplating sludge.

In this study, the behavior of heavy metal transformation during the co-thermal treatment of hazardous waste incineration fly ash (HWIFA) and Fe-containing hazardous waste (including hazardous waste incineration bottom slag (HWIBS) and electroplating sludge (ES)) was investigated. The findings demonstrated that such a treatment effectively reduced the static leaching toxicity of Cr and Pb. Moreover, when the treatment temperature exceeded 1000 °C, the co-thermal treated sample exhibited low concentrations of dynamically leached Cr, Pb, and Zn, indicating that these heavy metals were successful detoxified. Thermodynamic analyses and phase transformation results suggested that the formation of spinel and the gradual disappearance of chromium dioxide in the presence of Fe-containing hazardous wastes contributed to the solidification of chromium. Additionally, the efficient detoxification of Pb and Zn was attributed to their volatilization and entry into the liquid phase during the co-thermal treatment process. Therefore, this study sets an excellent example of the co-thermal treatment of hazardous wastes and the control of heavy metal pollution during the treatment process.

Fluidization-melting characteristics of fly ash from municipal solid waste incineration.

Fly ash (FA) from municipal solid waste incineration contains hazardous substances such as dioxins, furans, and heavy metals. Melting FA has proved to be an effective method for reducing volume and mass, while also rendering the waste harmless. However, during the melting process, the addition of a fluxing agent with calorific value is currently necessary to increase melting capacity and reduce energy consumption, which presents a challenge. To tackle this issue, a fluidization-melting technology for a fuel/FA mixture is proposed, wherein a fuel source is employed in the melting process, producing ash that can serve as a fluxing agent. To test this approach, rice husk (RH) was utilized as fuel in a small-scale fluidization-melting test. The objective of this study was to examine the operation parameters of the platform and the characteristics of the resulting product, and to evaluate the harm reduction effect of the slag and its potential for resource utilization. The operating temperature was set at 690 °C in the thermal modification unit and at 1450 °C in the melting furnace, resulting in stable operation and continuous liquid slag discharge. The leaching toxicity of heavy metals in the obtained slag was lower than the standard limit, achieving harmless disposal of FA. However, the resource utilization potential of the obtained slag is limited due to its failure to meet the criteria of vitrified substance and environmental quality requirements. These limitations could be addressed by promoting the combustion of carbon in the melting furnace and accelerating the cooling rate of the slag in the quenching unit.

Wet shaking table operating parameters optimization for maximizing metal recovery from incineration bottom ash fine fraction.

Municipal solid waste incineration bottom ash has emerged as a secondary source of valuable metals, including aluminum and copper. Specifically, the fine fraction, with a particle size less than two millimeters, exhibits average grades of 2.5 g/kg for copper and 10.0 g/kg for elemental aluminum. Gravimetric concentration equipment, such as wet shaking tables, is widely used in the mining and recycling industries to concentrate materials based on density. However, the optimization of these devices typically relies on a trial-and-error approach. This paper presents a statistical model that optimizes the crucial working parameters of the wet shaking table for recovering elemental aluminum in a light product mineral matrix and copper in a high-density product. The statistical analysis highlights that upper values of shaking amplitude are beneficial for both the recovery and grade of copper and aluminum in the obtained products. Conversely, variations in other parameters, such as wash water or desk tilt, yield contrasting effects on grade and recovery. By precisely adjusting the working parameters of the device, the analyses demonstrate that copper enrichment of up to 45 times can be achieved in the product smaller than 500 µm and up to 15 times in the 500-2000 µm product, resulting in the recovery of approximately 65 % of the total copper.

Improving long-term operation performance of hazardous waste rotary kiln incineration facilities: An evaluation with DEA model.

Hazardous waste rotary kiln incineration, as the most effective and comprehensive technology to reduce and detoxify waste, generally faces problems such as low load rate and short continuous operating periods. However, there are few studies on the actual operation of such facilities and evaluation of their technical efficiency. Based on the 77-week time-series data of the case company, this study introduces in-depth key operating parameters and evaluates long-term technical efficiency through the data envelopment analysis (DEA) method. The results show that the continuous operating period of the rotary kiln incineration facility can reach more than half a year, with an average load rate of 91.7%. In the analysis of 9 input indicators, the amount of injected activated carbon could not be effectively evaluated due to the lack of relevant standards and online real-time monitoring of dioxins, which might become a weak link in the control of flue gas pollution. The average comprehensive technical efficiency of rotary kiln incineration facilities was 0.939, of which the average pure technical efficiency was 0.949 while the average scale efficiency was 0.989. With 33 of the 77 decision-making units being invalid, there is scope for improvement. The amount of incineration could be increased by 5.34%, and among the input variables, dosage of urea, calcium hydroxide and lye with a relatively high improvement ratio. Based on the results, targeted suggestions were proposed to advance the scientific and precise compatibility of hazardous waste, strengthen the control of dioxin emissions, and promote the intelligent control of the entire process.

Waste incineration and heat recovery hybridized with low-focus fresnel lens solar collectors for sustainable multi-generation; A thorough techno-economic-environmental analysis and optimization.

Biomass, including municipal solid waste, and solar energy are two of the inevitable sources for future decarbonized energy systems. Fresnel lens thermal collectors using cheap micro-structured foils is an interesting emerging medium-temperature solar thermal design that might be of high practical value, provided that its fluctuating output is managed. This study proposes a hybrid solar-waste solution using this type of collector for multi-generation via an Organic Rankine Cycle. The cycle is specially designed for supplying low-grade heat, power, and industrial heat (which is a very critical sector to be decarbonized) taking advantage of the generated stable solar-waste medium-temperature heat at zero emission level. To achieve this optimal design, the article conducts a thorough energy-exergy-economic-environment (4E) analysis of the system and employs the non-dominated sorting genetic algorithm (NSGA II) for the optimizations. A benchmarking analysis is also conducted to show the importance of industrial heat supply in this cycle. The results show that this hybridization, owing to the cheap and flexible heat delivery of the waste incinerator as well as the low cost of the solar collectors, is very effective for efficient and cheap multi-generation. Especially for industrial heat supply, the competitive levelized cost of energy (LCOE) of 23.96 €/MWh is obtained, which is way lower than today's achievable costs in the industry.

Experimental study on solidification/stabilization of leachate sludge by sulfoaluminate cement and MSWI by-products.

Leachate sludge is generated from the biochemical treatment sludge tank for disposing the leachate from landfill municipal solid waste (MSW). It has the characteristics of high water content and high organic matter content. Sulfoaluminate cement (SAC) is used as the main curing agent, and municipal solid waste incineration (MSWI) by-products are used as auxiliary curing agents to solidify/stabilize the leachate sludge. The influences of SAC content and MSWI by-products content on the strength and solidification mechanism of the leachate sludge are investigated by unconfined compressive strength (UCS) test and micro-observation tests. Moreover, the leaching concentration of heavy metals of the solidified samples is analyzed by leaching toxicity test. The results show that the UCS of the solidified samples increases with an increase in cement content. When the cement content is larger than 20%, the UCS of the solidified samples satisfies the strength requirement of landfill. The enhancing effect of bottom ash on the cement-solidified samples is slight. The fly ash is a good auxiliary curing agent for improving the UCS of cement-solidified samples, and the optimal dosage of fly ash is 5% and 15% for the solidified samples with 10 ~ 30% and 40 ~ 50% cement content, respectively. Ten percent fly ash can replace 10% cement to achieve better solidification effect for the solidified samples. The leaching concentration of heavy metals in the solidified sample with 30%/40% cement and 15% fly ash/bottom ash can satisfy the strength and leaching toxicity requirements of landfill. The immobilization of heavy metal of the cement and MSWI by-products solidified samples is mainly achieved through physical adsorption, physical encapsulation, ion exchange, and chemical precipitation.